Version=5

;24.08.17 mod by ML and SW, Erfurt
;04.09.17 mod by SW Erfurt - Shrinkage and Scattering for Dental Applications

[General]
Name="DentaMODEL"
Industry="Dental"
Manufacturer="Asiga"
Revision=7
Heater Temperature=30 ;°C
Minimum Temperature=0
Heater Enable=true ;true/false
Color="#E6D4BF"

[Cure]
Temperature=0
Minimum Temperature=0
Time=300
Power Level=100
Vacuum=true
Vacuum Target=0.010
Minimum Vacuum=0.050
Gas=false
Gas Cycles=1

[:/405/General]
Printer Classes=[Pico, "Pico 2", PRO, "PRO UV405", "MAX", "PRO 4K UV405", "Max 2 405", "Ultra 405"]

[:/405/Curing]
; T [mW/cm²·s , mm]

Light Intensity Control=1
Light Intensity = 7

; 2018-03-23, MAX (405 nm), 7 mW/cm², 22.0 °C
Z=[	6.1	,	0.03	,	7	]
Z=[	7.5	,	0.05	,	7	]
Z=[	9.3	,	0.07	,	7	]
Z=[	11.5	,	0.09	,	7	]
Z=[	14.2	,	0.11	,	7	]
Z=[	17.5	,	0.13	,	7	]
Z=[	21.6	,	0.15	,	7	]
Z=[	26.7	,	0.17	,	7	]
Z=[	33.0	,	0.19	,	7	]
Z=[	40.8	,	0.21	,	7	]
Z=[	50.4	,	0.23	,	7	]
Z=[	62.3	,	0.25	,	7	]
Z=[	76.9	,	0.27	,	7	]
Z=[	95.1	,	0.29	,	7	]
Z=[	117.5	,	0.31	,	7	]
Z=[	145.1	,	0.33	,	7	]
Z=[	179.3	,	0.35	,	7	]
Z=[	304.4	,	0.4	,	7	]
Z=[	2526.1	,	0.6	,	7	]

Offset=0.08
Burn-In Layers=2
Burn-In Exposure=0.30 ; mm

; XY=[mw/cm²·s, mm]
;XY=[17.5, 0.03 ]
;XY=[21.7, 0.04 ] 
;XY=[30, 0.05]
;XY=[350, 0.051]
XY Compensation=-0.01
Scale=[1.006, 1.006, 1] ; determined with SC=0 and AA=1



[:/Gen-2UV/General]
Printer Classes=["Pico UV385", "PRO UV385", "MAX UV385", "PRO 4K UV385", "Max 2", "Ultra"]  ;mainly MAX, PRO is overridden below

[:/Gen-2UV/Curing]
; T [mW/cm²·s , mm]

;Light Intensity Control=1
;Light Intensity = 4.5
;Z Compensation=0.050 ;@ 50 micron layers

;MAX UV @ 1.03 mW/cm²
Z=[	5.1	,	0.03	,	1.03	]
Z=[	6.6	,	0.05	,	1.03	]
Z=[	8.5	,	0.07	,	1.03	]
Z=[	11.1	,	0.09	,	1.03	]
Z=[	14.4	,	0.11	,	1.03	]
Z=[	18.7	,	0.13	,	1.03	]
Z=[	24.2	,	0.15	,	1.03	]
Z=[	31.4	,	0.17	,	1.03	]
Z=[	40.7	,	0.19	,	1.03	]
Z=[	52.8	,	0.21	,	1.03	]
Z=[	68.5	,	0.23	,	1.03	]
Z=[	88.8	,	0.25	,	1.03	]
Z=[	115.2	,	0.27	,	1.03	]
Z=[	149.5	,	0.29	,	1.03	]
Z=[	193.9	,	0.31	,	1.03	]
Z=[	251.4	,	0.33	,	1.03	]
Z=[	326.1	,	0.35	,	1.03	]
Z=[	624.9	,	0.4	,	1.03	]
Z=[	8423.0	,	0.6	,	1.03	]

;MAX UV @ 5.06 mW/cm²
Z=[	5.6	,	0.03	,	5.06	]
Z=[	7.0	,	0.05	,	5.06	]
Z=[	8.9	,	0.07	,	5.06	]
Z=[	11.2	,	0.09	,	5.06	]
Z=[	14.1	,	0.11	,	5.06	]
Z=[	17.7	,	0.13	,	5.06	]
Z=[	22.3	,	0.15	,	5.06	]
Z=[	28.2	,	0.17	,	5.06	]
Z=[	35.5	,	0.19	,	5.06	]
Z=[	44.7	,	0.21	,	5.06	]
Z=[	56.4	,	0.23	,	5.06	]
Z=[	71.0	,	0.25	,	5.06	]
Z=[	89.5	,	0.27	,	5.06	]
Z=[	112.8	,	0.29	,	5.06	]
Z=[	142.2	,	0.31	,	5.06	]
Z=[	402.8	,	0.4	,	5.06	]
Z=[	4071.3	,	0.6	,	5.06	]

;MAX UV @ 8 mW/cm² remeasured
Z=[	6.1	,	0.03	,	8.03	]
Z=[	7.5	,	0.05	,	8.03	]
Z=[	9.3	,	0.07	,	8.03	]
Z=[	11.5	,	0.09	,	8.03	]
Z=[	14.2	,	0.11	,	8.03	]
Z=[	17.5	,	0.13	,	8.03	]
Z=[	21.6	,	0.15	,	8.03	]
Z=[	26.7	,	0.17	,	8.03	]
Z=[	33.0	,	0.19	,	8.03	]
Z=[	40.8	,	0.21	,	8.03	]
Z=[	50.4	,	0.23	,	8.03	]
Z=[	62.3	,	0.25	,	8.03	]
Z=[	76.9	,	0.27	,	8.03	]
Z=[	95.1	,	0.29	,	8.03	]
Z=[	117.5	,	0.31	,	8.03	]
Z=[	145.1	,	0.33	,	8.03	]
Z=[	179.3	,	0.35	,	8.03	]
Z=[	304.4	,	0.4	,	8.03	]
Z=[	2526.1	,	0.6	,	8.03	]


Offset=0.060
Burn-In Layers=2
Burn-In Exposure=0.30 ; mm
; XY=[mw/cm²·s, mm]

;XY=[17.5, 0.03 ]
;XY=[21.7, 0.04 ] 
;XY=[30, 0.05]
;XY=[350, 0.051]
;XY=[, 0.045 ]
;XY Compensation=-0.03
XY Compensation=-0.01
Scale=[1.005, 1.005, 1] ; determined with SC=0 and AA=1

;Two-Step Exposure Border Width=1   ; was enabled, but it seems to give same results in shorter time for TSB=0


[Delays]
Burn-In Wait Time (After Exposure)=2 ; s
Burn-In Wait Time (After Separation)=5 ; s ; for material flowback
Normal Wait Time (After Exposure)=0.1 ; s

[:/PRO-Platform/General]
Printer Classes=["PRO UV385"]


[:/PRO-Platform/Curing]
; 2015-08-04, PRO2 UV (385 nm), 4,5 mW/cm². 25.7 °C
;MAX UV @ 1.03 mW/cm²
Z=[	5.1	,	0.03	,	1.03	]
Z=[	6.6	,	0.05	,	1.03	]
Z=[	8.5	,	0.07	,	1.03	]
Z=[	11.1	,	0.09	,	1.03	]
Z=[	14.4	,	0.11	,	1.03	]
Z=[	18.7	,	0.13	,	1.03	]
Z=[	24.2	,	0.15	,	1.03	]
Z=[	31.4	,	0.17	,	1.03	]
Z=[	40.7	,	0.19	,	1.03	]
Z=[	52.8	,	0.21	,	1.03	]
Z=[	68.5	,	0.23	,	1.03	]
Z=[	88.8	,	0.25	,	1.03	]
Z=[	115.2	,	0.27	,	1.03	]
Z=[	149.5	,	0.29	,	1.03	]
Z=[	193.9	,	0.31	,	1.03	]
Z=[	251.4	,	0.33	,	1.03	]
Z=[	326.1	,	0.35	,	1.03	]
Z=[	624.9	,	0.4	,	1.03	]
Z=[	8423.0	,	0.6	,	1.03	]

;MAX UV @ 5.06 mW/cm²
Z=[	5.6	,	0.03	,	5.06	]
Z=[	7.0	,	0.05	,	5.06	]
Z=[	8.9	,	0.07	,	5.06	]
Z=[	11.2	,	0.09	,	5.06	]
Z=[	14.1	,	0.11	,	5.06	]
Z=[	17.7	,	0.13	,	5.06	]
Z=[	22.3	,	0.15	,	5.06	]
Z=[	28.2	,	0.17	,	5.06	]
Z=[	35.5	,	0.19	,	5.06	]
Z=[	44.7	,	0.21	,	5.06	]
Z=[	56.4	,	0.23	,	5.06	]
Z=[	71.0	,	0.25	,	5.06	]
Z=[	89.5	,	0.27	,	5.06	]
Z=[	112.8	,	0.29	,	5.06	]
Z=[	142.2	,	0.31	,	5.06	]
Z=[	402.8	,	0.4	,	5.06	]
Z=[	4071.3	,	0.6	,	5.06	]

Offset=0.070
Burn-In Layers=2
Burn-In Exposure=0.3 ; mm



[:/Sliderless/General]
; Uncomment the following line to use sliderless mode as default for PRO
Printer Classes=["PRO UV385", PRO, "PRO UV405"]

[:/Sliderless/Delays]
Burn-In Wait Time (After Exposure)=2 ; s
Burn-In Wait Time (After Separation)=10 ; s ; for material flowback
Burn-In Wait Time (After Approach)=60 ; s
Burn-In Wait Time (After Slide)=0 ; s
Normal Wait Time (After Exposure)=0 ; s
Normal Wait Time (After Separation)=0.1 ; s ; for material flowback
Normal Wait Time (After Approach)=1 ; s
Normal Wait Time (After Slide)=0 ; s

[:/Sliderless/Curing]
Shrinkage Compensation Enable=true ; true/false ; gives a lot better surfaces for large crosssections (boar test)
Two-Step Exposure Border Width=1   ; gives a lot better surfaces for large crosssections

[:/Sliderless/Mechanics]
Slides per Layer=0

[:/Pico2/General]
Printer Classes=["Pico UV385"]

[:/Pico2/Mechanics]
Separation Velocity=4.95 ; mm/s

[:/MAX/General]
Printer Classes=["MAX UV385", "MAX", "Max 2", "Max 2 405"]

[:/MAX/Mechanics]
Separation Pressure Limit=300 ; g/cm²
Separation Velocity=4.3 ; mm/s

[:/4K/General]
Printer Classes=["PRO 4K UV385", "PRO 4K UV405"]

[:/4K/Mechanics]
Separation Pressure Limit=300 ; g/cm²
Separation Velocity=4.3 ; mm/s

[Mechanics]

[Support]
Leveling=true
Leveling Height=2.0
Tallest=false
Tallest Height=0.0
Slope=20
Side Feature=2.5
Spacing=2.0
Strength=40
Torsion=0
Intersupport=true
Contact=0.5
Island=0.8
Overshoot=0.8
MaximumWidth=1.5
Side Faces=20
AspectRatio=2.0